Reply To: Configure Conduit mLinux LoRa for Loriot server
Are you connected to internet through cellular or LAN? Network setup manual or DHCP? See dns setup files: http://www.multitech.net/developer/search_gcse/?qresolv.conf
View ArticleReply To: Configure Conduit mLinux LoRa for Loriot server
Thank you, Jason. I am connected LAN via Ethernet cable. I set static IP via /etc/network/interfaces – address, netmask, gateway, dns-nameservers (this one is a guess, does not work). The link you...
View ArticleReply To: Configure Conduit mLinux LoRa for Loriot server
OK, found your previous post here: http://www.multitech.net/developer/forums/topic/dns-configuration-on-mlinux/ I have it set up similr to your recommendation: # Wired interface auto eth0 iface eth0...
View ArticleReply To: Configure Conduit mLinux LoRa for Loriot server
Jason, thank you, it works as described here: http://www.multitech.net/developer/forums/topic/dns-configuration-on-mlinux/
View ArticleReply To: Instructions for installing python packages no longer work.
Try using this link instead of the other: https://bootstrap.pypa.io/ez_setup.py
View ArticleReply To: Microchip RN2903 join private conduit network (OTAA)
Hi, i have the same problem. Any update? Regards. Miguel
View ArticleClik here to view.
Reply To: stop serial mode, changed mtxdot XDOT-NA1-A00 MODULE SERIAL...
According to your instructions We’re back to the previous terminal state. ——————————————————– For 1: 1 serial communication The node of module 1 is 1234(16 char) and the node of module 2 is 5678(16...
View ArticleReply To: Error while installing custom App.
3) You should be able to use the postinstall step to do that. I think in the case you have described you will need two init scripts. One with just a start() to start the app before the LoRa WAN server...
View ArticleReply To: Error while installing custom App.
Ajay, Do you want to change the start order in a target run level? ie. “update-rc.d customapp stop 31 5″ If that is the case just remember that your custom app will need to be responsible for this on...
View ArticleConnecting an Arduino Shield to the UDK2
So I am trying to connect this 24V industrial I/O shield to the developer board (UDK2) connected to my mDot. I am trying to get a 4-20mA sensor to run through the shield and give my mDot a reading....
View ArticleReply To: Error while installing custom App.
Hi Jeff, For the stop levels i.e. 0, 1 and 6 the priority of the custom app is at 1 on my conduit, so its going to be run/shutdown after the lora-network-service and mosquitto has already been shut...
View ArticleReply To: Connecting an Arduino Shield to the UDK2
Can you link the pinout for the specific shield you’re using?
View ArticleReply To: Connecting an Arduino Shield to the UDK2
https://www.rugged-circuits.com/24v-industrial-tech-page I believe it’s towards the bottom of the page.
View ArticleReply To: Connecting an Arduino Shield to the UDK2
You’re using the 4-20mA inputs on that board, correct? Which input are you using? What ADC reading are you seeing across that 200 ohm sense resistor, if any?
View ArticleClik here to view.
Reply To: Connecting an Arduino Shield to the UDK2
I had the sensor connected to the 4-20 input, and the output connected to the GND header above. I am getting no current going through the connectors it seems. The voltage that seems to be coming out...
View ArticleReply To: Error while installing custom App.
Ajay, Other than making sure to re-install on firmware upgrade that we already discussed, I don’t see any issues with what you are doing. Jeff
View ArticleReply To: Connecting an Arduino Shield to the UDK2
According to the description of the current inputs for that board the ADC channel is measuring the voltage across a 200 ohm resistor. One potential problem is that the max voltage on the ADC pin is...
View ArticleReply To: Error while installing custom App.
Thanks Jeff for confirming. Yup will ensure on re-install of firmware the customapp priority levels are set correctly. Thanks, Ajay
View ArticleHow to send custom data from the Mdot to the gateway?
Hello, I am a novice and just trying to self learn. I am using a UDK2.0 with an MDOT connected to its X10, X11 pins, and I cnt seem to get it to send data to the gateway. How do I do this? Can anyone...
View ArticleReply To: Transmit in Progress Error when sending packets.
I am also interested in this error which i have recently been receiving, though on an xDot instead. I am running Private lora network with a custom app, US915mHz and most up to date libxdot-mbed5 with...
View Article