Lora communication with Multitech AEP gateway
Hi, I try to receive data from my Libelium Environment PRO on a Multitech Multiconnect Conduit AEP Gateway. To do this, I used examples given with the system. I am able to receive frames, but I am...
View ArticleConnecting the Multi tech gateway to things networks
Hi to all, I am a little new to LoRaWAN technology but have gathered some of the information up til now. I have a multi tech gateway MTCDT-H5-210A-AU with a lora chip in it MTAC-LORA-915 and couple of...
View ArticleReply To: connexion entre mon produit Adeunis et la multitech
Did you try to register the nodes with EUI values reversed? Reverse the DEV-EUI and APP-EUI values used previously. # lora-query -a <NET-ADDR> [CLASS] <APP-EUI> <DEV-EUI> [APP-KEY]...
View ArticleReply To: DNS Settings (mlunix)
Did you try: ping 8.8.8.8 How about: ping [gateway address]?
View ArticleReply To: connexion entre mon produit Adeunis et la multitech
j’ai échanger et il y a bien accepter la relation. Received CRC Errors 0 Duplicates 0 Join Duplicates 0 Join Requests 1 MIC Failures Total Packets 1 Sent Duplicates Acked 0 Packets Acked 0 Total Join...
View ArticleClik here to view.
Reply To: DNS Settings (mlunix)
Thanks for the suggestion… looks like the conduit firmware neglects (or needs to be done manually) to add the default route. This could be fixed using route add default gw [gw address] Annoyed,...
View ArticleReply To: Wifi networks not visible on 247A
Paul, Can you disable WiFi as WAN, reboot, and then see if the scan works? There is a limitation in the WiFi module on the Conduit such that if WiFi station or AP is enabled it will not be able to do...
View ArticleReply To: DNS Settings (mlunix)
Your netmask is questionable: netmask 255.255.255.252 10.x.y.z is usually class A. Your netmask would then be 255.0.0.0 I have never had problems with the gateway line in /etc/network/interfaces.
View ArticleReply To: DNS Settings (mlunix)
I should add that /etc/network/interfaces is ignored in AEP, I believe.
View ArticleHow are ‘NetID’ and ‘Address Range’ settings used in OTAA
Hello, We are using the AEP version of the MultiConnect Conduit for LoRaWAN communications. In the “LoRa Network Server Configuration” window there are three parameters in the “Network” section for...
View ArticleClik here to view.
Reply To: DNS Settings (mlunix)
These are just the IP addresses I was told to use, what the underlying network resembles, I can only guess. Regardless, it seems to be working… for now You are right saying that...
View ArticleData consumption using AT&T and Azure
We have an MTCDT-LAT1-U Conduit sending data to Azure over AT&T using a custom Python script written for the Conduit’s native MQTT/LoRa broker. A basic LoRa packet with an 8 character payload is a...
View ArticleReply To: Data consumption using AT&T and Azure
John, Are you doing encryption. Is this TCP or UDP? What messages are being sent to Azure? Is your connection good? If you have a signal that is weak, TCP will cause retransmissions at a high rate....
View ArticleReply To: Data consumption using AT&T and Azure
Jeff, We are not doing any encryption. Signal strength appears to be maxed. We are using TCP. Also, the ratios of “raw data” packet size to “sent” and “received” sizes is consistent between tests so I...
View ArticleReply To: Wifi networks not visible on 247A
Yes the Wifi AP is definitely not enabled. I will try what you suggest and get back to you Thanks Paul
View ArticleReply To: Data consumption using AT&T and Azure
John, Have you tried tcpdump on ppp0? That might shed some light on what’s going on if the data isn’t encrypted. Jeff
View ArticleUart on mDot
I used the uart (DIN,DOUT) on the mDot at 38400baud in order to communicate with another processor. When i put my interface board on the frozen around -20°C, the mDot generates a checksum error on my...
View ArticleReply To: Data consumption using AT&T and Azure
Jeff, Following is the tcpdump on ppp0. Unfortunately, my tcpdump interpretive skills are a bit lacking. While I am researching, any feedback/hints you might be able to give that might help point us...
View ArticleClik here to view.
Reply To: Wifi networks not visible on 247A
OK tried that, no difference. After I disabled Wifi as WAN, rebooted, then enabled it to do a scan, didn’t see anything. Then tried another reboot (Save and Restart), still no networks showing. Jumped...
View ArticleReply To: Descrypt MQTT package.
I have no clue where your data is coming from. What event is this taken from? Are you using the mtdot box hardware?
View Article