Reply To: Cannot Compile mDot Code
Ok, I am trying this. It says the build system is under heavy load and is timing out right now, so I think I will have to wait a bit to make sure it works but I will let you know!
View ArticleReply To: Frequency sub-band selection
I discovered there is a spectral scan utility. Does anyone have experience with this? http://www.multitech.net/developer/software/lora/spectral-scan/
View ArticleReply To: Frequency sub-band selection
MTAC-LORA-1.5 Card is needed. # mts-io-sysfs show lora/hardware-id
View ArticleReply To: Cannot Compile mDot Code
Hey Jason, I tried again now and it is now compiling, but giving me the following errors: imgur.com/a/OzsP8 When I put the program onto the mDot, it shows up but does not change the EUI and Key (which...
View ArticleConfiguring to work with MQTT broker with user name and password
I have my LoRa Network Server configured to publish messages to the Mosquitto MQTT broker. Currently this only works if I have “allow_anonymous true” set in the mosquitto.conf file. Is their a way to...
View ArticleReply To: Cannot Compile mDot Code
Nevermind, I figured it out. I needed to comment out the name and passphrase lines and uncomment the id and key lines. Thanks for your help Jason!
View ArticleClik here to view.
Reply To: Configuring to work with MQTT broker with user name and password
MQTT Name and password are not currently supported in network server.
View ArticleReply To: Configuring to work with MQTT broker with user name and password
Thanks for the fast response. I’m mainly concerned with not letting anyone from the outside connect and publish to the MQTT broker running on the Multitech gateway. I have the MQTT broker on the...
View ArticleReply To: Configuring to work with MQTT broker with user name and password
So you have enabled the MQTT broker on Conduit to use the public interface and bridge that connection using the mosquitto.conf file? I would write an app that consumes the MQTT messages from the local...
View ArticleReply To: Configuring to work with MQTT broker with user name and password
Yea, I updated the mosquitto.conf to bridge to another Mosquitto Broker running on a server. I’m currently pushing up all lora/+/up messages. I like your suggestion. I’ll disable the bridge, and just...
View ArticlemDot Class C fails to receive after 20min
Dear all, I am trying to send 1 packet every 4 seconds from a conduit Multitech gateway to a dot configured in class C. The conduit sends the 1byte payload packet every 4 Sec indefinitely. For the...
View ArticleReply To: mDot Class C fails to receive after 20min
Is the server requesting an ack from device? The server does not do retries yet. Perhaps it is waiting for ack.
View ArticleReply To: mDot Class C fails to receive after 20min
Hy Jason, The conduit does not wait an ack. It continue to send messages. I continue to see a différent messages pass to windows debug. I say the node stop receiving packets because i don’t have datas...
View ArticleClik here to view.
Reply To: mDot Class C fails to receive after 20min
I have a inject node connected to a function node. Then this function node is connected to lora out node and a debug node. In function node i have payload : ‘h’ + timestamp. In the debug i see ‘h’ +...
View ArticleReply To: mDot Class C fails to receive after 20min
i have connect serial’s node (uart) on my pc and i save the data in a file.
View ArticleCannot ssh into the MTCAP
Hi, I received my MTCAP today and was following the quick start guide. I powered it up and connected to my computer with the LAN cable. I statically gave an IP address in my laptop. Now i can ping to...
View ArticleReply To: Cannot ssh into the MTCAP
If you received an MTCAP with 3.3.6, the password was mistakenly set wrong. Here is the readme with the password at the end: http://www.multitech.net/mlinux/images/mtcap/3.3.6/Readme.txt
View ArticleInternet connection with Ethernet
Hi, using the Conduit without a SIM card is it possible to connect to the Internet only through the Ethernet connection? Actually when I ping for example 8.8.8.8 I get: `root@mtcdt:~# ping 8.8.8.8...
View Article