factory reset not working
Hi. I haven’t used the conduit AEP in a while and now i can’t communicate with it. i’m trying a factory reset per these instructions:...
View ArticleReply To: Upload message does not respect gateway channel
Multitech team can you comment on what Mark has called out, is this something that could be an issue on the MDot as well. Especially the ticker problem that has been described in one of Mark’s earlier...
View ArticleReply To: Empty Packet From the Gateway
Hi Alexis, Are you using Class A/Class C mode while transmitting data between the MDot and conduit. Because in Class A if you send a packet from the MDot to the conduit and the conduit needs to have...
View ArticleReply To: factory reset not working
Pascal, I looked at the code that handles the reset button press. It is handled in the mts-io kernel module and by the reset-monitor process. The kernel module keeps track of a short press (~5s), a...
View ArticleSending Data from one mDot to Multiple Conduits
Hello, We are trying to send the same data (Broadcast) from mDot to two Conduits. The Conduits share the same configuration including Network Name, Paraphrase and Frequency Sub Band. I am using OTA...
View ArticleReply To: Sending Data from one mDot to Multiple Conduits
The mDot will only join one Conduit in OTA. The session information is not shared between Conduits. ABP activation could be used to receive the broadcast from mDots. Perhaps an application on Conduit...
View ArticleReply To: factory reset not working
Hi, thank you for the reply and also appreciate the phone call with Steve! The reset button produces no effect, whether short, medium, or long. I tried many different ways. Also the console access...
View ArticleClik here to view.
Reply To: factory reset not working
Did you install any 3rd party software? TNN or Loriot packet forwarder? Can you connect device to internet? It should be able to complete boot. This reply was modified 3 hours, 26 minutes ago by...
View ArticleReply To: factory reset not working
Factory reset will restore omly configuration. This must be done with unit powered on. However in default setting the unit will be in gateway mode and not in DHCP client mode if you expect to connect...
View ArticleClik here to view.
PPPD is not retrying to connect
Hi, in our setup we are using PPPD to connect to a 3G network. On some sites we have a bad and varying signal quality, which makes that sometimes the carrier is lost during some hours. In some cases...
View ArticleReply To: setFrequencyBand() isn't works
Resolved by moving to opensource loramac-node stack.
View ArticleReply To: PPPD is not retrying to connect
Patrick, I’m pretty sure that pppd doesn’t automatically redial/reconnect. You will need to check the connection by pinging 8.8.8.8 or something like that, and if the ping fails restart pppd. Jeff
View ArticleReply To: PPPD is not retrying to connect
Jeff, Adding the persist option to /var/config/ppp/options makes pppd reconnect automatically when the connection is lost. This works quite well, except in the situation I’m describing. – Patrick.
View ArticleReply To: factory reset not working
Ok, I was hoping a factory reset would restore the original image as if the device was brand new again. I’ve been installing TTN and experimenting with a lot of other LoRaWAN network servers. It’s...
View ArticleReply To: PPPD is not retrying to connect
Patrick, We’ve found that we’ve had to still test our Internet connectivity even though pppd is up and has carrier and connectivity with the tower. We basically ping 8.8.8.8 and if over a given amount...
View ArticleReply To: factory reset not working
Pascal, There are some packages that had issues because they expected Internet connectivity in their boot scripts and would block until it was available. This would cause the boot to “hang” before the...
View ArticleReply To: factory reset not working
Hi Jeff, I seemed to have run into something similar. Is there a way to reset to factory settings from the putty command prompt? I pressed the reset button for over 20 seconds and everything is as is....
View ArticleReply To: factory reset not working
So I seemed to have managed to reset it to defaults, however I get the following error below and can’t seem to connect to the 192.168.2.1 ip and i am guessing it is because of the error below. udhcpc...
View ArticleReply To: Sending Data from one mDot to Multiple Conduits
Hello, Thank you for your reply! We switched the join mode to manual mode and On both conduits we created a node with same Network Address, network_session_key and data_session_key. It worked. But now...
View Articlehow to power on mdot peer to peer
Dear Sir, If i follow this command, how to power on each other mdot can be serial communcation? best, Paul. Configuration This example sets up each side with identical settings and starts serial data...
View Article