Reply To: mqtt path for getting lora message
Just following up for completeness sake, as I’m sure other people will hit this as well, so hopefully this helps somebody. We’d determined that an upper safe limit as to over all data message size...
View ArticleReply To: mqtt path for getting lora message
With ADR enabled the network can increase the datarate when the signal looks good. The end-device will lower the datarate when the signal is bad, realized by periodically missed packets. To enforce a...
View ArticleReply To: Can't connect to 192.168.2.1
Hi, I am having a very similar problem, the thing is that I could not make it work with this solution. I have model MTCAP-915-001A and I cannot connect to IP 192.168.2.1. I have already manually...
View ArticleAEP 5.3.0: no way to set APN?
I just upgraded one of my conduits to 5.3.0 for testing and I don’t see a way to set the APN. When I compare the cellular configuration screens between a 5.2.1 conduit and a 5.3.0 conduit, the APN...
View ArticleReply To: AEP 5.3.0: no way to set APN?
Hi EG Part of the Verizon certification process has the Verizon network download the APN to the modem/SIM which is why if the modem detects a Verizon SIM, the APN field is omitted from UI. There are...
View ArticleReply To: Can't connect to 192.168.2.1
Hi Tomas You could use a paperclip straightened out and try to factory default the device by using the paperclip to hold the “Reset” button in for 31 seconds. The MTCAP device should factory default...
View ArticleDEV_TIME_REQ (LoRaWAN 1.0.3+)
Is the MAC command DevTimeReq supported by the Lora server of Conduit ?
View ArticleReply To: DEV_TIME_REQ (LoRaWAN 1.0.3+)
I didn’t try yet, but I will. What is the time replied ? UTC or local ?
View ArticleReply To: DEV_TIME_REQ (LoRaWAN 1.0.3+)
GPS Time See page 41 of LW1.0.4 spec https://lora-alliance.org/resource_hub/lorawan-104-specification-package/
View ArticleReply To: No Network Interfaces Available
Update: The client replaced an Ethernet cable, and connection was reestablished. However, it’s still a mystery how the downloaded config for waninfo could report false for available, enabled and...
View ArticleInstall custom apps automatically
Hello, Is possible to configure then Conduit to automatically detect and install custom apps from de SD Card? The idea is to put the app installer tgz in a SD card and use it to deploy the app in...
View ArticlePacket Forwarder STOPPED and RUNNING
Hi, I´m having a problem with my gateway, Multitech MTCAP, via de AEP GUI. The Packet Forwarder stops and after a while starts running again, and after some seconds shows the red STOPPED again. Is...
View ArticleReply To: AEP 5.3.0: no way to set APN?
Hi EG Part of the Verizon certification process has the Verizon network download the APN to the modem/SIM which is why if the modem detects a Verizon SIM, the APN field is omitted from UI. There are...
View ArticleReply To: Can't connect to 192.168.2.1
Hi Tomas You could use a paperclip straightened out and try to factory default the device by using the paperclip to hold the “Reset” button in for 31 seconds. The MTCAP device should factory default...
View ArticleDEV_TIME_REQ (LoRaWAN 1.0.3+)
Is the MAC command DevTimeReq supported by the Lora server of Conduit ?
View ArticleReply To: DEV_TIME_REQ (LoRaWAN 1.0.3+)
I didn’t try yet, but I will. What is the time replied ? UTC or local ?
View ArticleReply To: DEV_TIME_REQ (LoRaWAN 1.0.3+)
GPS Time See page 41 of LW1.0.4 spec https://lora-alliance.org/resource_hub/lorawan-104-specification-package/
View Article