What is the difference between a mLinux Conduit HW and a NodeRED Conduit HW?
If you see this web page (http://www.multitech.net/developer/products/conduit/conduit-led-descriptions/), it shows the front panel is different between an mLinux Conduit HW and a NodeRED Conduit HW....
View ArticleMTCDT-H5 can't be accessed
Hi Forum, I appended two lines to /etc/network to start custom services. These services are being developing. I have no access to the GW neither from normal SSH nor from debug USB. Via USB I see the...
View ArticleModem Network Registration Problem
Hello, I am using a MultiTech MultiModem model MTCBA-G-F2 Serial No. 5001425F. I know that this is different from the iSMS models, but I thought this section was the most appropriate to address my...
View ArticleReply To: MTCDT-H5 can't be accessed
Tibor, You should be able to get the login prompt via the USB debug port by hitting the key. -Brandon
View ArticleReply To: What is the difference between a mLinux Conduit HW and a NodeRED...
Hoon, Nope, the only differences are: 1. Part number 2. Firmware loaded at factory 3. Front panel decal Yes, if you load mLinux firmware on an AEP Conduit, the leds will behave as programmed in the...
View ArticleReply To: Node-Red Start & Stop.
Ajay, I’m not aware of any way to do this. The only way to make sure your data is saved it to save your data periodically or on each update. -Brandon
View ArticleReply To: Node-Red Start & Stop.
Thanks Brandon. How about the startup scenario, is there a way to read the data stored in a file before the flows begin processing any data? Thanks, Ajay.
View ArticleReply To: Modem Network Registration Problem
Hello Alin The modem model MTCBA-G-F2 is a dual band modem designed to be used in North America and supports GSM/GPRS at 850/1900MHz. I feel that in Romania the dual GsM/GPRS frequencies used are...
View ArticlelibmDot version 2.0.3 broke virtual terminal debug stream with MTMDK-ST-MDOT
When building with the version 2.0.3 release of libMDot on the Mbed web platform and using a Mdot attached to a MTMDK-ST-MDOT development board on can not set a baud rate using either Serial...
View ArticleReply To: libmDot version 2.0.3 broke virtual terminal debug stream with...
Update Was finally able to get a readable debug stream with this combination mbed library version 117 mbed-rtos version 117 libmDot version 2.0.3 Terminal emulator baud 115200 debug.baud(115200); call...
View ArticleReply To: MTCDT-H5 can't be accessed
Hi Brandon, I’m just getting these messages and no chance to log in. No response for enters. Of course no Ethernet cable attached now. Any idea? T INFO: Acquired EUI xxxxxxxxxxxxxxxxxxxxxx from...
View ArticleReply To: Modem Network Registration Problem
Steve, Thank you very much for the useful reply.
View ArticleReply To: MTCDT-H5 can't be accessed
Hello Tibor Can you please post the serial number of your MTCDT-H5 device. The serial number is located on a sticker on the bottom of the device. My only other suggestion at this time to recover the...
View ArticleReply To: MTCDT-H5 can't be accessed
Hi Steve, I tried resetting the device several times but no improvement achieved. I can’t see anything happening on the debug screen as pushing the PB for even more than 30 seconds. No reboot...
View ArticleReply To: MTCDT-H5 can't be accessed
Hi Tibor Seems the device is non-functional and unrecoverable in the field. That leaves us little choice but to ask that you send the device into MultiTech for warrantee repair (or replacement)....
View ArticleReply To: MTCDT-H5 can't be accessed
Hi Steve, I simply started two binaries to connect to Loriot and forgot to send them bg. Mea Culpa. I’m shipping the GW Monday. Best regards, Tibor
View ArticleHow can I install mLinux firmware on an AEP conduit?
There is an mLinux firmware installation instruction here at http://www.multitech.net/developer/software/mlinux/using-mlinux/flashing-mlinux-firmware-for-conduit/. But it looks like it describes how...
View ArticleReply To: Node-Red Start & Stop.
Ajay, >>is there a way to read the data stored in a file before the flows begin processing any data? Yes is Node-RED evaluates nodes as defined in the flows JSON config. So the the first node...
View ArticleReply To: Join mode differences
Thanks for the detailed response. If I have a mDot::getInstance and soon after a deep sleep call without any network interaction such as a join or send data will this break the session? Thanks Andrew
View ArticleClik here to view.
Reply To: Join mode differences
Andrew, Are you referring to a situation like this? mDot state Session state ---------- ------------- reset/boot N/A | getInstance() OTA mode: session is reset | AUTO_OTA mode w/preserve session off:...
View Article