Reply To: LBT activation
MTCDT-0.0 seems to be upgradable. Is this right? Thanks for clarification.
View ArticleReply To: LBT activation
For MTCDT it depends on the installed card. MTAC-LORA-1.5 has the FPGA and can be upgraded. MTAC-LORA-1.0 does not have an FPGA.
View ArticleClik here to view.
Reply To: LBT activation
It appears I do something wrong: "lbt_cfg": { "enable": true, "rssi_target": -80, "chan_cfg": [ {"freq_hz":867100000, "scan_time_us":5000}, {"freq_hz":867300000, "scan_time_us":5000},...
View ArticleMTAC-XDOT-NA1
We have a Multitech Conduit (MTCDT-LAT1-247A-US) gateway. In AP1 we have a MTAC-GPIOB accessory card. In AP2, we have a MTAC-XDOT-NA1 card. However, when I issue the mts-io-sysfs show ap1/product-id...
View ArticleClik here to view.
Reply To: LBT activation
It appears the v33 LBT firmware does not support frequencies below 915 MHz. LBT is not required for LoRaWAN use in EU868, LoRaWAN uses duty-cycle. See lines 125-140. The minimum lbt frequency is...
View ArticleClik here to view.
Reply To: LBT activation
I know it is not required, but as far as I know EU let’s you decide between using LBT or DutyCycle. Anyway seems that is not a problem of the gateway. EDIT: Seems limited by program. FPGA should...
View ArticleClik here to view.
Reply To: LBT activation
Can official FW FPGA versions be burned in Multitech cards with fpga? Just want to check if the v33 posted in git and yours is the same. EDIT: Git seems to have 2 versions of v33, 915 and 863 This...
View ArticleConnection of packet forwarder as range extender / network bridge
Hello, We are trying to connect one MTCDT-246A / 1.4.3 – packet forwarder, to transmit packets from nodes to another MTCDT-246A / 1.4.3 – Network Server, via Lora. Nodes are associated to the packet...
View ArticleReply To: What is the new lora-query command for adding nodes in MTCAP
Hi Jason, I was able to add all the keys based on the curl commands. Now when i see the LoraWan > Key Management i find my device and the keys associated to it. Now i fail to connect but in the log...
View ArticleBuild AEP image with custom package
Hi, I need to install the flask and sqlalchemy pip packages into the Conduit APE gw, in order to run our software. Can I build a custom SO image with this 2 packages pre install. Cumps,
View ArticleReply To: Connection of packet forwarder as range extender / network bridge
This is not possible with packet forwarder. There is no method for forwarding packets over lora in a bi-directional manner. I could be possible to repeat the received packets on the forwarding...
View ArticleReply To: What is the new lora-query command for adding nodes in MTCAP
CRC-ERROR is probably not caused by your device. See Network Communications > Possible Issues section of the linked troubleshooting guide....
View ArticleClik here to view.
Reply To: LBT activation
They are not the same and the mts-fpga-loader utility will not install them. We may look at including the 863 version of firmware in a future version. They should be functionally equivalent. The...
View ArticleReply To: Build AEP image with custom package
Luis, The AEP firmware is proprietary, so you will not be able to build a custom image of that firmware. However, you can use the mLinux distro based off of Yocto found here:...
View ArticleClik here to view.
Reply To: Build AEP image with custom package
Multitech have plans to include this packages in a near future? Cumps,
View ArticleClik here to view.
Reply To: Remote site access via rCell (VPN)
I have a partial solution. It turns out you need a Verizon data plan with a fixed / public IP to be able to see the rCell from outside. (Bring money!) So now I have initiated contact from the outside...
View ArticleReply To: What is the new lora-query command for adding nodes in MTCAP
somehow this link does not solve my problem. Is there some way i can debug this?
View ArticleReply To: What is the new lora-query command for adding nodes in MTCAP
Please open a support ticket at support.multitech.com and provide full configuration and log info.
View ArticleReply To: SPIFFS
For the record, it seems the mDot spits out [ERROR] SPIFFS_remove failed -10002 when you change the join mode, but that doesn’t seem to be an issue. Had me running a goose chase for a while.
View Article