Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN static IP
Summary I cannot access any of the configuration interfaces through the WAN static IP. Remote Access Management is enabled for all WAN config interfaces. Copied static IP from Device Information...
View ArticleReply To: Multitech git down?
Jeff, will try that. meanwhile, can you point me to the location where I can get the source in a tarball for 3.3.6? Manoj
View ArticleReply To: Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN...
Albert, Have you enabled access via WAN for HTTPS and SSH on the Conduit? Under Administartion->Access Configuration there are Web Server and SSH panes where you can enable via HTTPS and WAN. Jeff
View ArticleReply To: Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN...
Hi Jeff; Thanks for the response. Yes, my apologies for not being clearer; this is what I meant with “Remote Access Management is enabled for all WAN config interfaces” and “Redirect to HTTPS has no...
View ArticleReply To: Multitech git down?
Manoj, Under http://www.multitech.net/developer/downloads/ there is a Conduit: mLinux Model section, and the mLinux MTCDT 3.3.6 download is located in that section. Jeff
View ArticleReply To: Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN...
Albert, Thank you for clarifying. I definitely recommend talking to the provider first to see what they are allowing for incoming traffic. Then proceed from there. Jeff
View ArticleReply To: Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN...
Spoke with cellular service provider. It is a public, static IP. There are no restrictions on their side on this line. They even performed a network reset, forcing the device to register again (at...
View ArticlePacket forwarder not seen
Hello, we have 2 MultiConnect Conduit devices with LoRa chip. One of them is used as a LoRa Network Server and the other is used as a LoRa Access Point. The packer forwarder runs on LoRa AP. The...
View ArticleReply To: Packet forwarder not seen
Are you using mLinux or AEP? What version? Is this a setup you had working at one point and now it is not working? Can you elaborate on the network problem causing the LoRa AP to stop? The network...
View ArticleReply To: Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN...
Albert, Please file a portal case at support.multitech.com. They will be able to give you more dedicated help. Jeff
View ArticleReply To: Packet forwarder not seen
We are using mLinux: Linux mtcdt 3.12.27 Originally we had only one MT MC Conduit LoRa GW. We used the factory settings. It worked properly. We bought another LoRa GW, any my collague set it as a...
View ArticleReply To: Packet forwarder not seen
This init script is used only if the Conduit is to be configured for packet forwarder only mode. On a network server Conduit is should be disabled. /etc/default/lora-packet-forwarder On the Network...
View Articlemlinux problem
Hello, community: I have placed a service in the folder /etc/init.d and when I start the operating system, the system does not run, therefore, this service blocks the system and does not load the...
View ArticleReply To: mlinux problem
You can use u-boot to re-flash the firmware: http://www.multitech.net/developer/software/mlinux/using-mlinux/flashing-mlinux-firmware-for-conduit/
View ArticleReply To: Unable to use HTTP config UI on MTCDT-LVW2-247A v1.4.3 via WAN...
Done. Thanks Jeff. Kind regards.
View ArticleAccessing Conduit (MTCDT-LAT1-246A-US) remotely over cellular
Can anyone provide guidance as to accessing an AEP Conduit (Linux 3.12.27r13/AEP v1.4.3) over AT&T? We can get to the Linux OS fine when on Ethernet (over SSH) but not sure how to handle on...
View ArticleReply To: DNS Settings (mlunix)
Hello I have always the same problem, I con’t connect to Internet from my mlunix What can I do ?what means dnsmaq and how can I configure it ? I set up gatway in address and netmasq in the interface...
View Articlemosquito-sub up event disappeared
When I initially run the command “mosquito_sub -v -t lora/+/+”, I got the log like this: lora/00-04-a3-0b-00-1c-10-86/packet_recv...
View ArticleReply To: mosquito-sub up event disappeared
The frame counter (83 and 93) in the later “packet_recv” events is lower than the last “up” event (111). The network server will reject packets with lower than last frame counters to prevent replay...
View ArticleReply To: Packet forwarder not seen
I disabled LoRa packet forwarder in file /etc/default/lora-packet-forwarder. I also removed global_conf.json and local_conf.json files. Then I tried to start lora_pkt_fwd from /var/run/1 directory but...
View Article