Reply To: ABP mDot downlink issues?
Ok thanks! Also, I just reset my Downlink frame counter to zero, even though loraserver’s uplink counter reset when I reset the mDot with an iteration of my firmware. I also set the Datarate in the...
View ArticleWAN failover (Ethernet and 3G)
Can someone send me a script and explain how to configure eth0 as primary WAN interface and ppp0 as secondary WAN interface? Best regards.
View ArticleWAN failover (Ethernet and 3G)
Can someone explain or send a script how to configure eth0 as primary WAN interface and ppp0 as secondary WAN interface? Best regards.
View ArticleReply To: Only single Network Key?
Hey, why no response? From:http://www.multitech.net/developer/software/lora/introduction-to-lora/ Each end-device has a different set of encryption keys. This ensures the rest of the network remains...
View ArticleReply To: Only single Network Key?
The unique encryption keys referred to are the Session keys used after the join. Best practice for overall security is unique AppKeys per device as you are trying to configure. lora-query is the...
View ArticleReply To: Only single Network Key?
Hello, Jason This indeed was the problem: Be sure that the app-eui configured with the dev-eui does NOT match the NetworkID assigned to the Conduit. Otherwise it will validate the join against the...
View ArticleAddition of node-red-contrib-s7 1.3.0
Hi everyone, Is it possible to add node-red-contrib-s7 1.3.0 S7 Endpoint configuration node to nodes list in AEP conduit, and how to do it is possible? Thanks. Boyko
View ArticleReply To: Addition of node-red-contrib-s7 1.3.0
Boyko, You can use the “npm install node-red-contrib-s7comm” with the –prefix option to point to /opt/node-red/node_modules. ie. npm install node-red-contrib-s7comm –prefix /opt/node-red/node_modules...
View ArticleReply To: Addition of node-red-contrib-s7 1.3.0
Thanks Jeff. I’ll try, however it might be a case that the conduit may not accept upgrade nodes vers. higher than 0.10.X, due to instruction set. Boyko
View ArticleReply To: Addition of node-red-contrib-s7 1.3.0
Boyko, The 0.10.x restriction applies to node-js, not to the node you’re trying to add. I did not see any minimal version of node-js required for the s7comm node. Jeff
View ArticleReply To: Addition of node-red-contrib-s7 1.3.0
Thanks Jeff, that’s a good news, I’ll try. Boyko
View ArticleReply To: Internet connection for mLinux conduit
Hi, I had to fix 2 things: First add the gateway ip (router) second fix the DNS problem I added the two following lines in /etc/network/interface after ip-adress and netmask: ipaddress 192.168.2.1...
View ArticleReply To: How is network key calculated from passphrase?
Nevermind, I found this http://www.multitech.net/developer/forums/reply/reply-to-name-and-passphrase-to-appeui-and-networkkey-5/
View ArticleQuestion about xDOT
Hi all, I would like to connect xDot with external device using serial port. All data that xDOT receive from LoRa Gateway need to be transferred to serial port. Also, all data it receives from serial...
View ArticleCreate my own LoRaWAN network.
Hi, This is my architeture : I have some nodes as sensors, mutlitech conduit gateway as gateway and a computer as server. and I would like to gather information of all my sensors on a local server(...
View Articlelora_pkt_fwd
I am trying to configure a basic packet forwarder for my LoraWAN but nor the start script nor the manual way reaches to make it work. With the init script it always seemed to start properly, but in...
View ArticleReply To: lora_pkt_fwd
$ mts-io-sysfs show lora/product-id MTAC-LORA-868 $ mts-io-sysfs show lora/hw-version MTAC-LORA-1.0 This card is a USB card and must use the /opt/lora/basic_pkt_fwd or gps_pkt_fwd binaries. v3.x...
View ArticleReply To: lora_pkt_fwd
I do not now and ever have had basic_pkt_fwd on my install. I thought it to be a mistake in the manual. Could you tell me the name of the package from which I can install this executable?
View ArticleReply To: lora_pkt_fwd
mLinux lora recipes http://git.multitech.net/cgi-bin/cgit.cgi/meta-mlinux.git/tree/recipes-connectivity/lora See lora-packet-forwarder-usb Pre-built packages, match your mLinux version....
View ArticleReply To: Question about xDOT
I think you might be misunderstanding what LoRa can do. From your description you seem to suggest the xDot is being used as a serial link replacement and can receive and transmit at will. This is not...
View Article