mDot with DHT library
I’ve run into issues using the mDot with this common temperature/humidity sensor library: https://developer.mbed.org/users/Wimpie/code/DHT/ I’m not able to get readings using a DHT22 sensor. Just to...
View ArticleReply To: Installing AEP image on mLinux conduit
Hi Eric, You can flash either mLinux image or AEP image on any Conduit. However, from the mLinux to AEP version, you need to contact our Support Portal for an instruction/script of converting from...
View ArticleReply To: AEP 1.3.2 – custom application support
Eric, There is documentation on the type of custom applications that are supported and also on custom application created at:...
View ArticleReply To: MTSMC-H5.R2-SP with MTUDK2-ST-CELL: Only echoing back AT commands
Hi Fahad At this point I would encourage you to register and open a support portal case at https://support.multitech.com/support/login.html We can perform additional troubleshooting and the portal...
View ArticleNode-Red / Lora and GSM
Hello, I have a question about the operation of Node-Red / Loar and HTTP module. GSM and no Ethernet connection. The GSM connection is still active or it does raise every request? Is there an exmple...
View ArticleReply To: mDot with DHT library
I’ve used this sensor or an equivalent (AM2302) with this library on port PA_0 without issues. This pin was chosen as it was available on the PCB I’ve developed for the mDot. Andrew
View ArticleReply To: BLE (Bluetooth Low Energy) Support on MDot.
I have used the mDot with a Microchip RN4020 BLE module and have been able to use this to create a LoRa with BLE temperature sensor using one of the built in profiles. For a laugh, the probe was...
View ArticleReply To: long (~1 second) wake up times for mDot
Not sure about your versions, but for libmDot 14 I’ve been using mbed 121 and mbed-rtos 110 as the latest version combinations that work without error. Later versions of mbed-rtos wont compile at all....
View ArticleReply To: mDot Eagle library
Yes I did create an Eagle footprint for the mDot, but only the through hole version. I was looking to include the SMD pads as an alternative technology within the library but never finished it. I’ll...
View ArticleReply To: Internet connection issue
I am having ERR_CONNECTION_TIMED_OUT problem in my Pc.
View ArticleReply To: mDot Eagle library
Andrew, We will be releasing a developer guide for the xDot which will contain mechanical drawings, pinouts, etc. You may be able to get this info now via a portal case. Cheers, Mike
View ArticleReply To: BLE (Bluetooth Low Energy) Support on MDot.
Hi Andrew, How much Additional work did you need to do on the mDot side to get it to work with this BLE module? Also does it not have an SPI/I2C interface to communicate with? Thanks, Yogesh
View ArticleReply To: mDot Eagle library
From what I heard, the xDot developer guide should be available soon if not by tomorrow morning: http://www.multitech.net/developer/products/multiconnect-dot-series/multiconnect-xdot/
View ArticleReply To: Internet connection issue
I found my fix http://www.deskdecode.com/err_connection_timed_out/ its only my chrome who’s creating the problem i just open this on my chrome “chrome://settings/resetProfileSettings” and clcik on...
View ArticleReply To: Changes in Serial behavior after F4
Sorry for the long pause but this got put on our back burner for a little while and we just now revisited it. After an entire Saturday of poking this with a stick the problem actually appears to have...
View ArticleReply To: conduit mLinux + mDot Box
Hi Bryan, thanks for your reply. I configured my conduit according to the link that Jason mentioned. Now when I turn on the mDot Box and select any mode, the display shows “joining”, then “waiting…”...
View ArticleStep debug using online compiler
Hi, I am planning to use MTDOT-EVB to develop custom firmware to read input data and send using LoRa card. I came to know that compiler is available on-line and we can build code on-line. I would like...
View ArticleReply To: Step debug using online compiler
Dinesh, The online compiler does not support debugging. You’ll have to use a local IDE. We have published a wiki page outlining how you can do this:...
View Article